多年专注于可靠性测试设备
企业已通过质量管理体系认证和CE认证
现货供应|即日响应|长期质保|长期维护
多年专注于可靠性测试设备
企业已通过质量管理体系认证和CE认证
▶ DELAY TIME 是在【10.7 继电器设定画面】被设置的时间。
▶ LSP = LOW SP，MSP = MIDDLE，HSP = HIGH SP，NPV = NOW PV，NSP = NOW SP。
▶ LD = LOW DIFFERENCE，HD = HIGH DIFFERENCE，T = ON/OFF SIGNAL。
▶ 根据PV值来判断ON/OFF SIGNAL 动作 | |
设定 | ON/OFF SIGNAL 动作 |
① NPV < LSP ▶ ALWAYS : OFF |
|
② LSP <= NPV < MSP ▶ NPV >= NSP–LD : ON ▶ NPV < NSP–LD : OFF |
|
③ MSP < NPV <= HSP ▶ NPV >= NSP + HD : ON ▶ NPV < NSP + HD : OFF |
|
④ NPV >HSP ▶ ALWAYS : OFF |
|
[图面10-8] IS设定画面
1. TARGET：选择要使用的IS 对象。
2. TYPE：选择要使用的IS 种类。
3. BAND：选择内部信号的动作方向。
4. IS RANGE & DELAY：
1. 范围低：设定内部信号的下限值。
2. 范围高：设定内部信号的上限值。
3. 延时：设定内部信号的延迟时间。
☞ 在定值运行中，如果设置了变化率(SLOPE)，“TSP”的动作就是与程序控制的“TSP”一样，如果不设置变化率(SLOPE)，“TSP”作为“SP”来动作。
在BAND=INB的条件下 | 在BAND=OUTB的条件下 |
|
|
☞ 如果TYPE选择PV，就会存在回差（不能变更）的滞后现象
▶ 根据设定值来判断INNER SIGNAL 动作 | |
设定 | INNER SIGNAL 动作 |
▶ INPUT = 0.0 ~ 100.0 → 回差 = 0.5 ▶ OPER. MODE = PROG ▶ ITEM = HUMI ▶ TYPE = PV ▶ RANGE LOW = 30.0% ▶ RANGE HIGH = 50.0% ▶ DIRECT = IN BAND ▶ DELAY TIME = 00.00 |
|
▶ INPUT = 0.0 ~ 100.0 → 回差 = 0.5 ▶ OPER. MODE = PROG ▶ ITEM = HUMI ▶ TYPE = PV ▶ RANGE LOW = 30.0% ▶ RANGE HIGH = 50.0% ▶ DIRECT = OUT BAND ▶ DELAY TIME = 00.00 |
|
▶ INPUT = 0.0 ~ 100.0 ▶ OPER. MODE = PROG ▶ ITEM = HUMI ▶ TYPE = SP ▶ RANGE LOW = 30.0% ▶ RANGE HIGH = 50.0% ▶ DIRECT = IN BAND ▶ DELAY TIME = 00.10 |
|
▶ INPUT = 0.0 ~ 100.0 ▶ OPER. MODE = PROG ▶ ITEM = HUMI ▶ TYPE = TSP ▶ RANGE LOW = 30.0% ▶ RANGE HIGH = 50.0% ▶ DIRECT = OUT BAND ▶ DELAY TIME = 00.00 |
|
[图面10-9] DI设定画面
① 输入故障报警名称
[图面 10.7-1] DO CONFIG设定画面第 1 画面
[图面 10.7-2] DO CONFIG设定画面第2画面
扫一扫关注蜜桃臀一区二区三区
扫一扫关注蜜桃臀一区二区三区
